2025-06-13T18:41:00
permalink Post: 11900793
OK, another hour spent going through all the posts since I was on last night...
I won't quote the relevant posts as they go back ~15 pages, but a few more comments:
TAT errors affecting N1 power set: The FADEC logic (BTW, this is pretty much common on all Boeing FADEC) will use aircraft TAT if it agrees with the dedicated engine inlet temp probe - but if they differ it will use the engine probe . The GE inlet temp probe is relatively simple and unheated, so (unlike a heated probe) a blocked or contaminated probe will still read accurately - just with greater 'lag' to actual temperature changes.
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Fuel contamination/filter blockage: The fuel filters have a bypass - if the delta P across the filter becomes excessive, the filter bypasses and provides the contaminated fuel to the engine. Now this contaminated fuel could easy foul up the fuel metering unit causing a flameout, but to happen to two engines at virtually the same time would be tremendous unlikely.
Auto Thrust thrust lever retard - the TO lockup in the logic makes this very unlikely (it won't unlock below (IIRC) 400 ft., and even that requires a separate pilot action such as a mode select change or thrust lever movement). And if it did somehow happen, all the pilot needs to do is push the levers back up.
Engine parameters on the FDR: I don't know what exactly is on the 787 FDR with regards to engine parameters, but rest assured that there is plenty of engine data that gets recorded - most at one/second. Getting the FDR readout from a modern FDR is almost an embarrassment of riches. Assuming the data is intact, we'll soon have a very good idea of what the engines were doing
I won't quote the relevant posts as they go back ~15 pages, but a few more comments:
TAT errors affecting N1 power set: The FADEC logic (BTW, this is pretty much common on all Boeing FADEC) will use aircraft TAT if it agrees with the dedicated engine inlet temp probe - but if they differ it will use the engine probe . The GE inlet temp probe is relatively simple and unheated, so (unlike a heated probe) a blocked or contaminated probe will still read accurately - just with greater 'lag' to actual temperature changes.
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Fuel contamination/filter blockage: The fuel filters have a bypass - if the delta P across the filter becomes excessive, the filter bypasses and provides the contaminated fuel to the engine. Now this contaminated fuel could easy foul up the fuel metering unit causing a flameout, but to happen to two engines at virtually the same time would be tremendous unlikely.
Auto Thrust thrust lever retard - the TO lockup in the logic makes this very unlikely (it won't unlock below (IIRC) 400 ft., and even that requires a separate pilot action such as a mode select change or thrust lever movement). And if it did somehow happen, all the pilot needs to do is push the levers back up.
Engine parameters on the FDR: I don't know what exactly is on the 787 FDR with regards to engine parameters, but rest assured that there is plenty of engine data that gets recorded - most at one/second. Getting the FDR readout from a modern FDR is almost an embarrassment of riches. Assuming the data is intact, we'll soon have a very good idea of what the engines were doing
17 users liked this post.
2025-06-13T18:58:00
permalink Post: 11900812
OK, another hour spent going through all the posts since I was on last night...
I won't quote the relevant posts as they go back ~15 pages, but a few more comments:
TAT errors affecting N1 power set: The FADEC logic (BTW, this is pretty much common on all Boeing FADEC) will use aircraft TAT if it agrees with the dedicated engine inlet temp probe - but if they differ it will use the engine probe . The GE inlet temp probe is relatively simple and unheated, so (unlike a heated probe) a blocked or contaminated probe will still read accurately - just with greater 'lag' to actual temperature changes.
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Fuel contamination/filter blockage: The fuel filters have a bypass - if the delta P across the filter becomes excessive, the filter bypasses and provides the contaminated fuel to the engine. Now this contaminated fuel could easy foul up the fuel metering unit causing a flameout, but to happen to two engines at virtually the same time would be tremendous unlikely.
Auto Thrust thrust lever retard - the TO lockup in the logic makes this very unlikely (it won't unlock below (IIRC) 400 ft., and even that requires a separate pilot action such as a mode select change or thrust lever movement). And if it did somehow happen, all the pilot needs to do is push the levers back up.
Engine parameters on the FDR: I don't know what exactly is on the 787 FDR with regards to engine parameters, but rest assured that there is plenty of engine data that gets recorded - most at one/second. Getting the FDR readout from a modern FDR is almost an embarrassment of riches. Assuming the data is intact, we'll soon have a very good idea of what the engines were doing
I won't quote the relevant posts as they go back ~15 pages, but a few more comments:
TAT errors affecting N1 power set: The FADEC logic (BTW, this is pretty much common on all Boeing FADEC) will use aircraft TAT if it agrees with the dedicated engine inlet temp probe - but if they differ it will use the engine probe . The GE inlet temp probe is relatively simple and unheated, so (unlike a heated probe) a blocked or contaminated probe will still read accurately - just with greater 'lag' to actual temperature changes.
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Fuel contamination/filter blockage: The fuel filters have a bypass - if the delta P across the filter becomes excessive, the filter bypasses and provides the contaminated fuel to the engine. Now this contaminated fuel could easy foul up the fuel metering unit causing a flameout, but to happen to two engines at virtually the same time would be tremendous unlikely.
Auto Thrust thrust lever retard - the TO lockup in the logic makes this very unlikely (it won't unlock below (IIRC) 400 ft., and even that requires a separate pilot action such as a mode select change or thrust lever movement). And if it did somehow happen, all the pilot needs to do is push the levers back up.
Engine parameters on the FDR: I don't know what exactly is on the 787 FDR with regards to engine parameters, but rest assured that there is plenty of engine data that gets recorded - most at one/second. Getting the FDR readout from a modern FDR is almost an embarrassment of riches. Assuming the data is intact, we'll soon have a very good idea of what the engines were doing
2025-06-13T22:05:00
permalink Post: 11900958
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Two thoughts re TCMA: 1) Is it possible a false TCMA activation could have occurred just before, or concurrently with, the a/c leaving the ground, with the resulting loss of thrust and electrical power not being apparent for another (say) 10s); 2) As you say two simultaneous failures very unlikely... except that it did happen to that ANA flight, albeit during ground state.
2025-06-14T20:48:00
permalink Post: 11901821
Another hour spent sifting through the stuff since last night (my sympathies to the mods
). A few more comments:
"Real time engine monitoring" is typically not 'real time' - it's recorded and sent in periodic bursts. Very unlikely anything was sent from the event aircraft on this flight.
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
). A few more comments:
"Real time engine monitoring" is typically not 'real time' - it's recorded and sent in periodic bursts. Very unlikely anything was sent from the event aircraft on this flight.
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
67 users liked this post.
2025-06-14T21:27:00
permalink Post: 11901855
Another hour spent sifting through the stuff since last night (my sympathies to the mods
). A few more comments:
"Real time engine monitoring" is typically not 'real time' - it's recorded and sent in periodic bursts. Very unlikely anything was sent from the event aircraft on this flight.
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
). A few more comments:
"Real time engine monitoring" is typically not 'real time' - it's recorded and sent in periodic bursts. Very unlikely anything was sent from the event aircraft on this flight.
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
5 users liked this post.
2025-06-14T21:39:00
permalink Post: 11901865
TCMA
Which side of V1 does TCMA lurk? If a pilot closes the throttles to abort, does the system allow it? After all, "too low thrust" is outside the contour....
Ya know, when every conceivable possibility (or close) has been de wormed, it"s usually something impossible, or too fearful...(Or dishonest, fraudulent, criminal ....etc ,?
Which side of V1 does TCMA lurk? If a pilot closes the throttles to abort, does the system allow it? After all, "too low thrust" is outside the contour....
Ya know, when every conceivable possibility (or close) has been de wormed, it"s usually something impossible, or too fearful...(Or dishonest, fraudulent, criminal ....etc ,?
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
2 users liked this post.
2025-06-14T21:59:00
permalink Post: 11901875
From tdracer
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
2025-06-14T22:13:00
permalink Post: 11901888
From tdracer
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
1 user liked this post.
2025-06-14T23:20:00
permalink Post: 11901949
... The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) ...
5 users liked this post.
2025-06-14T23:54:00
permalink Post: 11901974
From tdracer
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Of course you can have two or three systems that are coded by different teams, using different languages, running in different hardware, even if they are fed from the same sensors, as long as you have many sensors (as tdracer has indicated, 5 inputs on the 747 for instance - although only needing 2 to be true does seem to reduce that margin for error somewhat).
If these two or three systems all have to send independent signals to the downstream hardware (the engine in this case) and the engine requires more than one signal to take the dangerous action like shutdown, then you're more protected, but that doesn't seem to be how the 787 works from the descriptions here by the experts like td and fdr. But please correct me if I'm wrong on that.
Its hard to imagine how else you could simultaneously cut both engines any other way, as tdracer said, other than human action or by software command. And software command means software failure. So information and discussion about exactly how redundant the software that takes this decision is would seem a good direction to move this discussion in. Is it truly only redundant 'internally' to itself, the module that sends this message to the engines? We heard about the 32 bit overflow bug that can shutdown engines - is it really that hard to believe that it has no other similar bugs when that one slipped through the testing?
2025-06-15T01:43:00
permalink Post: 11902040
MELs?
From tdracer
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
2025-06-13T18:41:00
permalink Post: 11903417
OK, another hour spent going through all the posts since I was on last night...
I won't quote the relevant posts as they go back ~15 pages, but a few more comments:
TAT errors affecting N1 power set: The FADEC logic (BTW, this is pretty much common on all Boeing FADEC) will use aircraft TAT if it agrees with the dedicated engine inlet temp probe - but if they differ it will use the engine probe . The GE inlet temp probe is relatively simple and unheated, so (unlike a heated probe) a blocked or contaminated probe will still read accurately - just with greater 'lag' to actual temperature changes.
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Fuel contamination/filter blockage: The fuel filters have a bypass - if the delta P across the filter becomes excessive, the filter bypasses and provides the contaminated fuel to the engine. Now this contaminated fuel could easy foul up the fuel metering unit causing a flameout, but to happen to two engines at virtually the same time would be tremendous unlikely.
Auto Thrust thrust lever retard - the TO lockup in the logic makes this very unlikely (it won't unlock below (IIRC) 400 ft., and even that requires a separate pilot action such as a mode select change or thrust lever movement). And if it did somehow happen, all the pilot needs to do is push the levers back up.
Engine parameters on the FDR: I don't know what exactly is on the 787 FDR with regards to engine parameters, but rest assured that there is plenty of engine data that gets recorded - most at one/second. Getting the FDR readout from a modern FDR is almost an embarrassment of riches. Assuming the data is intact, we'll soon have a very good idea of what the engines were doing
I won't quote the relevant posts as they go back ~15 pages, but a few more comments:
TAT errors affecting N1 power set: The FADEC logic (BTW, this is pretty much common on all Boeing FADEC) will use aircraft TAT if it agrees with the dedicated engine inlet temp probe - but if they differ it will use the engine probe . The GE inlet temp probe is relatively simple and unheated, so (unlike a heated probe) a blocked or contaminated probe will still read accurately - just with greater 'lag' to actual temperature changes.
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is only active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least one of each had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
Fuel contamination/filter blockage: The fuel filters have a bypass - if the delta P across the filter becomes excessive, the filter bypasses and provides the contaminated fuel to the engine. Now this contaminated fuel could easy foul up the fuel metering unit causing a flameout, but to happen to two engines at virtually the same time would be tremendous unlikely.
Auto Thrust thrust lever retard - the TO lockup in the logic makes this very unlikely (it won't unlock below (IIRC) 400 ft., and even that requires a separate pilot action such as a mode select change or thrust lever movement). And if it did somehow happen, all the pilot needs to do is push the levers back up.
Engine parameters on the FDR: I don't know what exactly is on the 787 FDR with regards to engine parameters, but rest assured that there is plenty of engine data that gets recorded - most at one/second. Getting the FDR readout from a modern FDR is almost an embarrassment of riches. Assuming the data is intact, we'll soon have a very good idea of what the engines were doing
3 users liked this post.
2025-06-14T20:48:00
permalink Post: 11903420
Another hour spent sifting through the stuff since last night (my sympathies to the mods
). A few more comments:
"Real time engine monitoring" is typically not 'real time' - it's recorded and sent in periodic bursts. Very unlikely anything was sent from the event aircraft on this flight.
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
). A few more comments:
"Real time engine monitoring" is typically not 'real time' - it's recorded and sent in periodic bursts. Very unlikely anything was sent from the event aircraft on this flight.
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
7 users liked this post.
2025-06-19T16:52:00
permalink Post: 11906189
TCMA - first off, I have to admit that this does look rather like an improper TCMA activation, but that is very, very unlikely. For those who don't know, TCMA is a system to shutdown a runaway engine that's not responding to the thrust lever - basic logic is an engine at high power with the thrust lever at/near idle, and the engine not decelerating. However, TCMA is
only
active on the ground (unfamiliar with the 787/GEnx TCMA air/ground logic - on the 747-8 we used 5 sources of air/ground - three Radio Altimeters and two Weight on Wheels - at least
one of each
had to indicate ground to enable TCMA). TCMA will shutdown the engine via the N2 overspeed protection - nearly instantaneous. For this to be TCMA, it would require at least two major failures - improper air ground indication or logic, and improper TCMA activation logic (completely separate software paths in the FADEC). Like I said, very, very unlikely.
I read one post in here of a 747 flaps retracting on takeoff. No Master Caution, no warnings. Apparently, due to some maintenance triggering a software glitch, the computer thought reverse thrust had been activated during a take off. Whether it was still in ground mode I don’t know.
Point is, being a software glitch in TMCA has already shut down two engines on a 787, I don’t see why the same or another software glitch in TMCA or somewhere else couldn’t do the same. Hadn’t this plane just been in for maintenance?
Last edited by T28B; 19th Jun 2025 at 17:05 . Reason: Formatting assistance
4 users liked this post.
2025-06-19T18:05:00
permalink Post: 11906239
Fuel valves and TCMA software updates?
Commanded engine cutoff - the aisle stand fuel switch sends electrical signals to the spar valve and the "High Pressure Shutoff Valve" (HPSOV) in the Fuel Metering Unit, commanding them to open/close using aircraft power. The HPSOV is solenoid controlled, and near instantaneous. The solenoid is of a 'locking' type that needs to be powered both ways (for obvious reasons, you wouldn't want a loss of electrical power to shut down the engine). The fire handle does the same thing, via different electrical paths (i.e. separate wiring).
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
As I've noted previously, a complete loss of aircraft electrical power would not cause the engines to flameout (or even lose meaningful thrust) during takeoff. In the takeoff altitude envelope, 'suction feed' (I think Airbus calls it 'gravity feed') is more than sufficient to supply the engine driven fuel pumps. It's only when you get up to ~20k ft. that suction feed can become an issue - and this event happened near sea level.
Not matter what's happening on the aircraft side - pushing the thrust levers to the forward stop will give you (at least) rated takeoff power since the only thing required from the aircraft is fuel and thrust lever position (and the thrust lever position resolver is powered by the FADEC).
The TCMA logic is designed and scrubbed so as to be quite robust - flight test data of the engine response to throttle slams is reviewed to insure there is adequate margin between the TCMA limits and the actual engine responses to prevent improper TCMA activation. Again, never say never, but a whole lot would have had to go wrong in the TCMA logic for it to have activated on this flight.
Now, if I assume the speculation that the RAT deployed is correct, I keep coming up with two potential scenarios that could explain what's known regarding this accident:
1) TCMA activation shutdown the engines
or
2) The fuel cutoff switches were activated.
I literally can come up with no other plausible scenarios.
In all due respect to all the pilots on this forum, I really hope it wasn't TCMA. It wouldn't be the first time a mandated 'safety system' has caused an accident (it wouldn't just be Boeing and GE - TCMA was forced by the FAA and EASA to prevent a scenario that had never caused a fatal accident) - and there would be a lot embarrassing questions for all involved. But I personally know many of the people who created, validated, and certified the GEnx-1B TCMA logic - and can't imagine what they would be going through if they missed something (coincidentally, one of them was at my birthday party last weekend and inevitably we ended up talking about what we used to do at Boeing (he's also retired)). Worse, similar TCMA logic is on the GEnx-2B (747-8) - which I was personally responsible for certifying - as well as the GE90-115B and the 737 MAX Leap engine - the consequences of that logic causing this accident would be massive.
I seem to remember Fred Dibner talking about how railway cars brake by draining the piston not by pressurising it, so trains will stop when supply lines break.
The electrical system updates to 787s for ADs and SBs - do any of these include software updates? For example the integer overflow causing GCU failsafe rectified under AD 2018-20-15. If so, who is writing and implementing these software updates? The original engineers? Their apprentices who had years long handovers? Or have they been outsourced and offshored? When these updates occur, does the entire system get tested and ratified or just the bit the bug fix is meant to fix? Because I\x92ve seen new bugs introduced by bug fixes in areas seemingly nothing to do with the original problem.